Single badge - this badge will always have the background colour of your car.
Plastichrome, a non tarnishing, non rusting durable material
Supplied with strong self-adhesive backing
Measures approximately 55mm by 98mm, 1.3mm thick
Super cleans fuel to ensure top performance
Captures dirt and grit as small as 40 microns before they can cause damage to intake system
Billet construction with triple chrome plate
Quickly & easily dismantled to clean brass element inside (wash with a little petrol)
Large size (125mm long), to suit 3/8" fuel lines
Heavy duty chrome plated bonnet pins.
Bonnet pins allow for fast complete removal of bonnets, bootlids, and other panels
This is usually beneficial for competition and custom cars, an added advantage is weight saving by means of allowing removal of standard catch assembly.
If the pins are to replace the front catch only then one set (2 pins) is required. If the complete removal of the bonnet is desired then two sets (4 pins) are usually required.
Pin length 100mm, pin thread M10
This header bolt set consists of 12 bolts and comes with a ball-head Allen socket that allows the bolts to be tightened at an angle. The bolts have a gold irridite polish, a 3/4 diameter, and fit vehicle applications with 3/8-16 threads (this includes the vast majority of American V8s as well as Rover V8). Spectre part number 46703
Insulates against under bonnet heat & sound. 5mm thick.
Aluminiumised self-adhesive heat shield mat reflects over 90% of radiant heat.
Also supplies protection on transmission tunnels, bulkheads, floorpans etc.
Smaller pieces or offcuts can be usefully employed to protect ECUs, fuel lines, hoses or any component you wish to keep cool.
Note that this product is designed to reflect heat and not designed for direct contact with manifolds/headers/exhausts. It will withstand temperatures up to 350 degrees F (176C) of direct contact. For direct contact with a heat source please see our other products.
Cut with tough scissors or Stanley knife, seal edges with alloy foil tape for neatest finish.
Very easy to apply but ensure surface is grease-free as nothing sticks to grease.
Please note that this material can be rolled but not easily folded for shipment, this results in increased shipping costs which will be quoted when you check-out.
Installation pictures here
1meter by 1meter sheet size (so if you order two you will get a sheet 1m by 2m), up to a maximum of 10m continuous length as that is the roll length.
We had to order 50 rolls to get the best price possible, but only have shelf space for 25 rolls of this product hence we need to clear some to make room.
Higher voltage gives better, fatter spark, resulting in added power, smoother response and better fuel economy.
Eliminates misfires, reducing plug fouling
40,000 volt output
Supplied complete with bracket & fitting hardware.
Fitted in seconds
Universal fitment for all non-ballasted ignition systems.
Suitable for standard or electronic distributors
Lucas part number DLB105
Supplied with universal adapter brackets for ease of fitting.
Can be mounted in front or behind the radiator - easily reversible depending on whether you wish to pull or push air
12 volt, 14 inch diameter (capacity 1990 Cubic Feet Minute, consumption 10.5) Width of fan at widest point (bearing point) 74.5mm
Often employed with alloy radiators for stunning effect.
Large rectangular oil catch tank kit
Capacity 1.1L. Unit measures 225mm tall by 80mm wide by 65mm deep.
Tank and bracket combined weight 1054gram
Fitted with twin top mounted inlets, bottom drain outlet, sight glass, breather stub & top screwed cap
Kit supplied with both 12mm OD (1/2") and 15mm OD (5/8") screw in barbed alloy pipe stubs
Pipe stubs are rotateable to enable angled connection for convenience of plumbing
Supplied complete with hose clips, mounting bracket, and 1 metre hose.
Polished alloy 1L oil catch tank kit.
Fitted with top mounted twin inlets, sight glass & magnetic drain plug.
Supplied with 100cm braided PVC hose & 4 hoseclips (additional hose can be purchased below if required)
Integral mounting clamp
Kit supplied with both 12mm OD (1/2") and 15mm OD (5/8") screw in barbed alloy pipe stubs, kit also includes blanking plug for use if only one inlet is required.
The slimline design of this tank means it will often fit available space where other tanks wont.
193mm high, 130mm wide, 53mm deep excluding pipework, 72mm deep including pipework. Weighs 490 gram
Click here for further details, installation photos
Brake master cylinder suits Triumph TR250 TR5 TR6 and others
Brand new boxed, not reconditioned
Part numbers: GMC234 64068822 218069
NB EEC manufactured item, not Chinese import